Pre-owned
Lamm equipment:
We provide a 5-year
warranty to the
original purchaser of
Lamm products obtained
through an authorized
Lamm dealer.
Pre-owned equipment does
not carry the warranty;
however, in certain
circumstances we might
be willing to sell the
remaining balance of the
5-year warranty term
(counting from the
original purchase date)
to interested
individuals. There
are a number of
conditions involved;
therefore, each such
case will be reconciled
individually.
Dealer
Demos
Under
the terms of our contract, Lamm dealers commit to keeping their demos for at
least one year. Dealer demos carry the following warranty to the first
buyer depending on the age of the equipment:
1) a 1-year warranty if the demos are less than 1 (one) or 1 (one) year
of age,
2) a 2-year warranty if the demos are 1+ (one+) through 3 (three)
years of age, and
3) no warranty if dealer demos are 3+ (three+) years of age.
However, the warranty on dealer demos will be validated only if the customer
sends in the warranty registration within the timeline indicated on the
warranty registration form (included in the manual). For more details,
see "Validating the Warranty" section on the Warranty
webpage.
we recommend replacing 6C19P
tube
about once a year to maintain the
best performance of the preamp
What
substitution tube types are recommended for the L1?
we recommend replacing 6C19P
and both 12AX3 tubes
about once a year to maintain the
best performance of the preamp
What
substitution tube types are recommended for the L2?
Instructions
for replacing the tubes in the L2
Ref.
Ventilation
slots located on the top cover of the
preamplifier and its power supply must not be blocked and the
distance between the top cover of the
power supply and any horizontal surface
located above the top cover should be
at least 4 inches.
We
don't offer remotes in a
conventional sense of the word.
However, we have a "remote turn
on/off" feature available when
the L2 Ref. preamp and the following LAMM amplifiers are used in
the same system: M1.1/M2.1/M1.2 Ref./M2.2/ML3 Signature. This
feature is activated by using remote control cables that
are ordered from us (one set -- 2 pcs. -- of remote
link cables is $49.90).
If you wish to order these
cables, there are two options
available regarding their lengths:
(1) one cable of the actual
length between the L2's
power supply and the
amp, and another a short link
between the amps OR
(2)
both cables of actual
length, each running from
the L2's power supply to
its respective amp
This
feature is activated by
"remote" switch(es)
located on the front panel
of the preamp's power
supply.
/
What
substitution tube types are recommended for the LL2?
What
substitution tube types are recommended for the LL2.1?
Ventilation
slots located on the top cover of
the preamplifier must not be blocked and the distance
between the top cover of the LL2 and
any horizontal surface located above the top
cover should be at least 4 inches.
What
substitution tube types are recommended for the LP2?
Warning
for proper packing before shipment
Ventilation
slots located on the top cover of
the preamplifier must not be blocked and the distance
between the top cover of the LP2 and
any horizontal surface located above the top
cover should be at least 4 inches.
You don't need to use shorting
plugs unless there is a strong RF in
your area. In this case, you
should just put the shorting plugs
in the unused inputs of the phono preamp
/
/
/
What
substitution tube types are recommended for the M1.1/M2.1?
What
substitution tube types are recommended for the M1.2
Reference/M2.2?
What's
special about the load selector switch on LAMM power amplifiers M1.2 Ref./M2.2/M1.1/M2.1?
IMPORTANT
-- as a
first-time user of the amps, you
should pay particular attention to
operating the "load"
and "power" switches
located on the rear panel of the
amp. These are so-called
locking switches, which means that
they don't operate by a simple
flick. You have to first
pull the switch toward yourself and
then move it up or down. This
type of switch is used to prevent
accident flicking. There is a
Warning insert right between the
plastic cover of the manual and its
title paper.
/
Warning
for proper installation of the V1
and V2 tubes prior to use
What
substitution tube types are recommended for the ML1?
What
substitution tube types are recommended for the ML1.1?
Instructions
for replacing the output tubes in
the ML1/ML1.1
Instructions
for replacing the front end tubes in
the ML1/ML1.1
/
/
Digital
voltmeter is a must for the user of
these amps
Warning
for proper installation of the V1
and V2 tubes prior to use
we recommend replacing
6N6P tube
about once a year (for ML2/ML2.1) and about once every two years (for ML2.2) to maintain the
best performance of the amp
What
substitution tube types are recommended for the ML2?
What
substitution tube types are recommended for the
ML2.1?
What
substitution tube types are recommended for the
ML2.2?
ML2.2
