PRODUCTS

Home News About Us Products Prices Warranty Awards Reviews Interviews Presentations
Shows Dealers FAQ Feedback Contact Us Links PayPal Sign guestbook
  View guestbook
OWNER'S PAGE

 

Products

Power amplifiers
       M1.2 Reference
     
description  specs
       M2.2
    
description  specs
       ML1.1
    
description  specs
      ML2.1
    
description  specs
ML3 Signature
    
description  specs
Preamplifiers
     LL2 (regular/deluxe)
     description  specs
     L2 Reference
    
description  specs
     LP2 (regular/deluxe)
                phono preamp
     description  specs

Prices

 

 

 
LINE-LEVEL PREAMPLIFIER

Rated Output Voltage*

 


from 20Hz-20KHz:

      
           1.0 Volts
RMS.
      

Voltage Gain

 



            7.87 + 2% or 17.92 + 0.2dB.

Frequency Response

 


from 1-30 Volts RMS:


(+ 0dB) 20 Hz, 20 KHz.
(- 3dB) 1.5 Hz, 400 KHz.

Slew Rate

 


Vout=28.8 Volts peak-to-peak of
square-wave signal, F=10KHz:


41 Volts per microsecond

Rise Time

 


Vout=28.8 Volts peak-to-peak of
square-wave signal, F=10KHz:


1 microsecond

Total Harmonic Distortion from 20 Hz - 20 KHz

 


Vout = 2 Volts RMS:

Vout = 30 Volts RMS:


no more than 0.03%

no more than 1%

IM Distortion 
(60Hz:7KHz  4:1) SMPTE:

 


Vout = 2 Volts RMS:

Vout = 30 Volts RMS into IHF load:


no more than 0.03%.

no more than 1%.

Inputs

 


Unbalanced 


gold plated single-ended RCA connectors.

Input Sensitivity*

 
             
Vout = 1.0 Volts RMS:


0.127 Volts RMS 2%.   

Input Impedance

 
 

50 KOhms + 10%.

Outputs

 
 
Unbalanced:

gold plated single-ended RCA connectors.

Corrected Output Impedance

 


typically 250 Ohms.

Noise

 

 
signal-to-noise ratio, below 2 Volts RMS output, unweighted


better than 84 dB.

Operating Temperature

 

 


-4 to +104 degrees Fahrenheit 
(-20 to +40 degrees Celsius) ambient.

Power Supply

 


nominal line voltage:

Input voltage range:


100-240 Volts, 50/60Hz.  

10%.

One power transformer, one filter choke, one full-wave vacuum rectifier, one solid-state analog non-switching voltage regulator.

AC voltage intensively filtered by special RFI power line filter.

Front/Rear Panel Controls: 

 

Front Panel Controls:

  • POWER switch.

  • MUTING switch.

  • LEFT GAIN control.

  • RIGHT GAIN control.

  • SELECTOR switches.

  • MONITOR switch.

  • LED control.

Rear Panel Connectors and Controls:

  • IEC 320 POWER INLET (3 lug).

  • EARTHING POST (gold plated).

  • Four pairs of INPUT CONNECTORS RCA for Line and Tape inputs.

  • Threee pairs of OUTPUT CONNECTORS RCA for Tape, Output 1, and Output 2.

Features

 


Pure class A vacuum tube design. All stages are single-ended.

High-current drive capability, in combination with unique single-ended class A circuitry, guarantee the preamplifier to drive any cable and any reasonable real world load, while maintaining its practically inaudible sonic signature.

This design is unique to LAMM INDUSTRIES, INC.

AC voltage selector:

100/120/220/230/240 Volts, switchable on the rear panel.


Safety:


Unique electronic protection circuit enables muting of the outputs until the preamplifier is stabilized after a turn-on, as well as functioning of the preamplifier in a "muting" mode during operation and automatic switching to muting in case the AC line drops or is interrupted.

Vacuum tube voltage regulator overload protection:

1 Amp slo-blo for 100/120 Volts,
0.5 Amps slo-blo for 220/230/240 Volts

General

 


Power Consumption:


Typically 40 Watts.  

Burn-in Time at Factory:

Minimum 72 hours.

Recommended Burn-in Time in End-user's System:

Minimum 200 hours.

Warm-up time:

Minimum 45 minutes.

Dimensions
(preamplifier and power supply have the same dimensions):

4.5 inches high x 19 inches wide x 13.875 deep + 1.375 inches for front handles.


Unit weight:

Shipping weight:


20 Lbs (9.1 Kg).  

36 Lbs (16.3 Kg).

Tube Complement:

  • V101 - 12AU7A (left channel, first amplification stage)
  • V103 - 6DJ8 (left channel, second amplification stage)
  • V102 - 12AU7A (right channel, first amplification stage)
  • V104 - 6DJ8 (right channel, second amplification stage)
  • V105 - 6X4/6202 (full wave voltage rectifier)